Qh150-1800 Type 5 Layer Corrugator Paperboard Ptoduction Line

• After-sales Service: Installation Commissioning Training
• Warranty: 1 Years
• Condition: New
• Certification: ISO 9001:2000, CE
• Automation: Automatic
• Suitable for: Paper, Corrugated Papercard Factory
• Model NO.: 1800
• Paper Thickness: Normal Specification Paper
• Transport Package: Ocean Shipping
• Specification: 1800 5-layers
• Trademark: QH-PACK
• Origin: China
• HS Code: 84393000
• Production Capacity: 50

Product Description

1. Manufacture width: 1800mm
2. Design speed: 150m/min   Working speed:120m/min
3. Note: The roll paper which is used to test the production speed should meet following requirements:
*Grade: Min. B                        * Moisture content: 11% ± 2%
 *Face paper: 100~250g/m2             * Liner paper: 100~150g/m2
* Corrugated paper: 100- 200g/m2
4. Flute profiles: B,C ,E flute(as per clients request)
5. Steam requirements
Steam consumption:2500kg/h     Air compressor pressure:0.8~1.1Mpa

1. Electricity: 380V, 50Hz,three-phase four wire type
2. Equipment Direction:Left or Right transmission will be according to client's requirements.

8. Factory request size:specific length as to the foundation of drawing

HB-I Hydraulic Mill Roll Stand

Structure and Features: 
1. Reel paper lift-lower, clamp, loosen, movement, contra position operated by hydraulic.feeding kraft / reel paper quickly.
2. Brake: multiple-point brake.
3. Each stand with two feeding trolly

Spec of stand:

1. Width:  Max: 1800mm        Min: 900mm 
2. Diameter: Max: Φ1500mm
3. Main Shaft Dia.: Φ242mm

4. Max Weight:3000Kg(One side)
5. Pneumatic Source Pressure(Mpa): 0.4---0.8Mpa

Spec of Hydraulic:
1. Working Pressure(mpa):16-18mpa           
2. lift hydraulic cylinder:Φ100×440mm
3. Clamping hydraulic cylinder: Φ63×1300mm 
4. Power Motor for Hydraulic Station:3KW --380V -- 50Hz
5. Magnetic Valve Voltage:380V 50HZ

Kraft paper feeding ground rack & trolly



Structure and Features:
1.To feed the kraft paper to reel stand.
2. The whole body of rack is under the ground, main frame: Model 14 channel steel with ¢ 20mm drawing bar weld together,overall length 6000mm.
3. Two racks for one reel stand to feed the kraft paper at both side.


SP-φ900 Preheter


Structure and Features:

1. The pre-heater roller is under the stander of the 1^st class(grade) pressure vessel of the national.
2. All the surfaces of every rollers have been grinded with high accuracy and chromed plated to less the resistance of paper preheating, long service of using life.
3. Electric to enlarge the preheating area, preheating area can be in 360° to adjust the preheating area.

Common Spec:
1. Working Width: 1800mm   

1. Diameter of the Preheater cylinder:Φ900mm      

   Preheating adjusting area by electric: 360°
3. Diameter of the roller for Preheating adjusting area by electric:Φ110mm

1. Steam temperature: 150-200ºC      Steam pressure: 0.8-1.3Mpa
2. Power:750W      380V 50Hz  Short Time(S2) Working Type

320CR Fingerless Single Facer


Glue Rollers:

Diameter	Φ240mm
Processing Way	Surface of glue roller is grinded, then with 25 line rut type net dot,then plating chrome Surface of glue banlance roller is grinded then plating chrome
Control Way	Airbag control of the Lifting Up-down
Glue Supply	Glue circulating system(storage tank+glue pump)

Corrugated Rollers:

Diameter	Down Roller:Φ320mm
Material	48CrMo high quality alloy steel, rigidity HRC55°-58°
Processing Way	The surface of upper-lower roller is plating chrome, annealing, hardening and tempering, surface grinded
Fulte Type	(U/V) A\B\C\E
Heating way of the reel paper	Steam heating

Press Rollers:

Diameter	Φ324mm
Material	medium steel (MS)45#
Processing Way	The surface is grinded then plating chrome, hardening and tempering(With Buffer)
Control Way	Airbag control of the Lifting Up-down

Preheater Rollers:

Diameter	UP Roller:Φ402mm
Material	seamless steel tube
Material band or origin	Tianjin Iron & Steel
All connected by flexible metallic tubes

Common Spec:

Style of Transmit cardboard	Vacuum Cover adsorbable style, Hight pressure Draw fan.with wind control Adjusting & noise deadening device.
Style of Control Roller	Pneumatic control the upper roller, pressure roller and glue roller
Driving Way:With frequency inverter

Common Spec:

1. Working width: 1800mm 
2. Design Speed:150m/min  Working Speed: 120m/min
3. Temperature: 180-200ºC   
4. Air pressure: 0.8-1.3Mpa

Spec of Motor:
Main Motor: 15kw  
Nominal voltage:380V 50Hz Continuous (S1) working Type


 CGM-F Gluer Machine


Structure and Features:

1. After the glue roller surface quenched, bore machining, surface grinding and doing balancing engraved pit style textured, coating evenly, consume less glue.

2. Glue roller rotation frequency motor control, the inverter control ensures glue line speed and duplex roller synchronous machines, and can operate independently.

1. Electric adjustment digital glue. Automatic cycle for glue, glue avoid sedimentation and viscosity stability.
2. Pneumatic presses structure, trimming the gap by the electric. Upper and lower layer are used independently variable frequency motor drive.
3. Sided machine speed signal measurements taken in order to achieve its synchronous operation. Man-machine interface display, easy operation.

Common Spec:

1. Preheater cylinder temperature range: 150-180ºC     Steam pressure: 0.8-1.2Mpa 
2. Pneumatic system: 0.4-0.7Mpa

Spec of the rollers' diameter

1. Glue roller:Φ269mm              Glue amount adjusting roller:Φ120mm
2. Down preheater roller:Φ320mm     Up preheater roller: Φ320mm    Paper roller:Φ85mm

Spec of Motor:

1. Glue rollers frequency variable motor: 3KW             

  Nominal voltage: 380V 50Hz Continuous (S1) working Type
 

1. Glue quantity adjustment motor:250W    

  Nominal voltage:380V 50Hz Short time (S2) working Type
 

1. Motor for adjusting the distance between the press roller and gluer roller: 250W

Nominal voltage:380V 50Hz Short time (S2) working Type
 

1. Glue pump motor: 2.2KW                         

  Nominal voltage: 380V 50Hz Continuous (S1) working Type

OHB Conveying Bridge

Structure and Features:

1. The Main Frame is connected with channel steel, and angle steel.
2. With Protecting Handrail on both sides and safety pedal, the operation side is installed with safety ladder, to make sure the safety and convenience of the worker.
3. Vacuum suction tension control, suction pipe with adjusting valve,draw fan power can be adjusted freely.
4. Correct the position by double guide posts , correct parts are driven by screw , fast and accuracy to position, steady to move.

Spec of the rollers:

1. Paper feeding rollers & tension rollers:Φ127mm      transport rollers:Φ110mm
2. Main tension drive rollers:Φ127mm       paper pass rollers and paper guide rollers:Φ110mm
3. Paper feeding rollers with belts:Φ110mm  

   
Spec of Motor:

1. Single face sheet draw motor: 3kw,   380V 50Hz Continuous (S1) working Type

2. Draw Fan Motor: 3kw,               380V 50Hz Continuous (S1) working Type
3. Paper width adjusting speed reducer: 250w     380V 50Hz Short time (S2) working Type




HPM Double Facer


Structure and Features:

1. Hot Plates' surfaces is grinded and then chromed plated,width:600mm.total 16 pieces of hot plates

   Hot plates are made by container plates, can pass the national first level pressure container standars

1. Hot plates adopts the compressed press rollers structure.Pressure roller lifting adopt pneumatic structure
2. Up convey belt left and right correct by auto with both sides, tension adjusting system; down belt manual small amount adjust.

4. Drive rollers' surface is wrapped by rubber, Y shape structure,with middle height,to make sure the board can be out smoothly
5. Main drive motor: Variable frequency motor, high force when low speed start, high speed adjusting range, steady to use,easy to mend.
6. Hot Plates' heat pipe piecewise control temperature.
7. Up belt adopt double cylinder S type  tensioning device
8. Under belt adopt S type manual correct tensioning device.

Common Spec:

1. Temperature requirement: 160-200ºC        Steam Pressure :0.8-1.3Mpa
2. Air pressure:0.6-0.9Mpa
3. Cool shaping length: 4m          Heating plates amount: 16pieces

Spec of Motor:

1. Main Drive Motor: 55kw Frequency

  Nominal voltage: 380V 50Hz Continuous (S1) working Type.


FTKM Electric Slitter Scorer


Structure and Features:
 1. Overcome the phenomenon of collapse the board when crop, smooth cutting, and the quality is improved
 2. The machine can move lift and right, adjust by cycloidal reducer.
 3. Cutter and line pressing adjustment convenient, error is ±0.5 mm, with automatic sharpening device
4. 5 blades 8 lines type, blade is made of tungsten alloy steel, life is more than 30,000 m

Technical parameter:
1. Max. width:1800mm                     
2. Specification: 5 knives 8 lines    
3. Min. Cut width:135mm           
4. Max cut width:1850mm         
Motor:
1. Knife motor:0.4KW               2. Knife driver motor:5.5KW

   NC-150 Cut Off Machine

Structure and Features:

1. Cutting length:500mm-9999mm.   Cutting precision:±1mm.
2. Knife shaft gear using precision forging steel material high frequency quenching, lateral clearance transmission , adopt the keyless connection mode, high driving accuracy.
3. Helical knife structure,type sawtooth knife,decrease cutting obstruction,low noise.
4. Balance treatment, high quality alloy steel for blade shaft,which helps to keep it good  stability.

5.Sun-shape wheels press cardboard in the front and the rear conveyer.The transporting is stable and with even pressure,which avoid jam caused or broken cardboard.
6. Precision adjustable gap gear, ensure blade precision engagement, running balance.
7. Machine base and wall panel adopt the grey cast iron, good rigidity, strong vibration resistance.

1. The servo controller control the servo motor, Taiwan  Eview 10.4 inch touch screen

Technical parameter:

1. Min. cut length:500mm           2. Max cut length:9999mm

1. Cut precision: uniform velocity ±1mm,    non-uniform velocity ±2mm

 Motor:

1. Main motor:18.5kw      Ac synchronous servo
2. Feeder motor:3 kw(Frequency control the speed)
3. Lubricating oil pump motor:0.25kw

    

SMA Sheet delivery machine




Structure & Features:
1. Weld by 14 # channel steel, electric to adjust the size of the board, pneumatic to control the the output on transverse direction, output speed can be adjusted electrically.
2. Corrugated sheet can be controlled output by foot switch when the mount or height of stacking corrugated sheet reaching the needs.
3. Longitudinal joint paper adopt wide conveyor belt conveyor.
Common Spec:
1,Max length of stacking:3000mm                        
2,Max height of stacking: 200mm       

Spec of Motor:
1. Main feeding frequency variable motor: 3KW  Frequency conversion motor
2. Transverse direction motor: 1.5KW    Three-phase asynchronous motor
3.Traveling motor: 1.5KW      Three-phase asynchronous motor  
  

 Glue Making System

1. Supply the glue for the single facers and double glue machine which use glue water
2. The glue in the glue storage tank are transported by the glue pump to the device.
3. The storage tank and glue supply tank are with mix device, to avoid the glue becoming into the sediment.
4. Glue making device: Main Glue mixer, Vice Glue Mixer, Glue storage tank, glue feeding pump, glue return pump.
5. Glue making system adopts the recycle glue supplying, the rest glue returns back, the glue from the return tank is transported to the tanks of each glue using device, to make the functions of the recycle and saving be true, and avoid the glue becoming into the sediment.
6. After the work finished, rest glue of each glue using devices are draw to the glue return storage tank to prepare for the next time using.
7. Responsible for technique guidance, and glue making way.

Product packaging

Company Information
QH-PACK GROUP CO.,LTD is specialized in manufacturing and export distributing of:

- Corrugated Cardboard Production Line (Corrugator for cardboard making),

- Computerized High Speed Flexo Printer Slotter Die-Cutter (Carton box machine),

- Others Convertion Machines(folder gluer,laminator,stitcher,flatbed die cutter),

- Paper Making Machines(kraft paper,flute&testliner,coating paper,tissue paper),

With 20 years experience of international trade and professional manufacture, plus a professional management and sales team, Quanheng Group has been dedicating on the above field enthusiastically to offer our customers with advanced equipments, competitive price, speedy delivery, and fully after service, so as to create value and winning power for our customers. Backed with strong financial support, talented personnel, sound reputation and high sense of commitment, turnover of QH-PACK has been rising rapidly and is heading to the future healthily and strategically. Businesses have covered CIS, Latin America, Middle East, Europe, North America, Southeast Asia and many other markets.



FAQ
1. who are we?
We are based in Hebei, China, start from 2017,sell to South America(20.00%),Mid East(20.00%),North America(10.00%),Eastern Europe(10.00%),Southeast Asia(5.00%),Africa(5.00%),Oceania(5.00%),Eastern Asia(5.00%),Western Europe(5.00%),Northern Europe(5.00%),Southern Europe(3.00%),Domestic Market(3.00%),Central America(2.00%),South Asia(2.00%). There are total about 5-10 people in our office.

2. how can we guarantee quality?
Always a pre-production sample before mass production;
Always final Inspection before shipment;

3.what can you buy from us?
corrugated cardboard production line,flexo printing slotting rotary die cutting machine,Folder glue machine,Flute lamianting machine,Die cutting and creasing machine

4. why should you buy from us not from other suppliers?
we are the professional manufacturer about the corrugated carton machine, and we have the professional sales part, after sales service trem, cooperate with us is your best choose!!!

5. what services can we provide?
Accepted Delivery Terms: FOB,CFR,CIF,EXW;
Accepted Payment Currency:USD,EUR;
Accepted Payment Type: T/T,L/C,D/P D/A,MoneyGram,Credit Card,PayPal,Western Union,Cash,Escrow;
Language Spoken:English,Chinese